Mercedes-Benz 400SEL Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(13)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(13)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a Mercedes-Benz 400SEL Tie Rod End Replacement is $158 with $63 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1993 Mercedes-Benz 400SELV8-4.2LService typeTie Rod End - Rear Right Inner ReplacementEstimate$240.67Shop/Dealer Price$289.59 - $396.98
1993 Mercedes-Benz 400SELV8-4.2LService typeTie Rod End - Rear Left Outer ReplacementEstimate$220.67Shop/Dealer Price$269.62 - $377.03
1993 Mercedes-Benz 400SELV8-4.2LService typeTie Rod End - Rear Right Outer ReplacementEstimate$220.67Shop/Dealer Price$269.62 - $377.03
1993 Mercedes-Benz 400SELV8-4.2LService typeTie Rod End - Front Left Outer ReplacementEstimate$220.67Shop/Dealer Price$269.58 - $376.96
1993 Mercedes-Benz 400SELV8-4.2LService typeTie Rod End - Front Right Inner ReplacementEstimate$220.67Shop/Dealer Price$269.65 - $377.08
1993 Mercedes-Benz 400SELV8-4.2LService typeTie Rod End - Front Right Outer ReplacementEstimate$220.67Shop/Dealer Price$269.62 - $377.03
1993 Mercedes-Benz 400SELV8-4.2LService typeTie Rod End - Front Left Inner ReplacementEstimate$225.67Shop/Dealer Price$274.38 - $381.61
1993 Mercedes-Benz 400SELV8-4.2LService typeTie Rod End - Rear Left Inner ReplacementEstimate$225.67Shop/Dealer Price$275.04 - $382.75
Show example Mercedes-Benz 400SEL Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(13)

Rating Summary
13
0
0
0
0
13
0
0
0
0

Attila

19 years of experience
963 reviews
Attila
19 years of experience
Mercedes-Benz 400SEL V8-4.2L - Car starts and then dies - Union, New Jersey
First his did great job and finally he said the issue was ignition coil.

Nicholas

21 years of experience
354 reviews
Nicholas
21 years of experience
Mercedes-Benz CLK320 V6-3.2L - Tie Rod End Replacement (Front Left Outer) - Denver, Colorado
Nicholas was very informative and explained exactly what he was repairing and why it was necessary. He was honest and sincere, worked quickly and cleanly. Very personable young fellow.

Travis

13 years of experience
611 reviews
Travis
13 years of experience
Mercedes-Benz CLS500 V8-5.0L - Tie Rod End Replacement (Front Right Inner) - Minneapolis, Minnesota
Travis was on time and prepared. Very helpful in describing the work that needed to be done compared to estimates from other auto repair quotes. Would definitely book him again in the future!

Damian

11 years of experience
465 reviews
Damian
11 years of experience
Mercedes-Benz C230 L4-2.3L - Tie Rod End Replacement (Front Left Inner, Front Right Inner, Front Left Outer, Front Right Outer) - Washington, District of Columbia
He explained everything in a way that even I could understand.

Excellent Rating

(13)

Rating Summary
13
0
0
0
0
13
0
0
0
0
Number of Mercedes-Benz Tie Rod End Replacement services completed
143+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

How to Buy a Personalized License Plate in New York
A A personalized license plate is one of the most popular ways to add fun flair to a New York vehicle. With a personalized license plate, you can show support for your favorite team or your alma mater, show off...
P0376 OBD-II Trouble Code: Timing Reference High Resolution Signal B Too Many Pulses
P0376 code means there is an irregularity with the high resolution timing reference signal coming from the PCM requiring urgent attention.
P0782 OBD-II Trouble Code: 2-3 Shift Malfunction
P0782 code means the PCM has detected a problem with the 2-3 shift function often due too faulty solenoids or transmission failure.

Getting random misfire code.

Your Chrysler sets a P0300 random or multiple misfire code when more than a 1.8% misfire rate is measured during two trips. Countless issues can set this code, from a vacuum leak to a bad coil pack. Your engine is...

Rough idle when engine is hot after 10 minutes of sitting

Based on the information you provided, It sounds like you may have sticking or leaking fuel injector (https://www.yourmechanic.com/services/fuel-injector-replacement). I suggest having the car looked at by a certified technician, like one from YourMechanic, who can diagnose your rough running symptoms...

Car has problem starting

If you suspect battery then I guess you're saying that the car has problems cranking; in that the starter motor seems to be turning more slowly when you turn the key. A car made in 2002 should probably be on...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com