Input-Output Sensor Replacement at your home or office.

Our certified mechanics come to you · Backed by our 12-month, 12,000-mile warranty · Get a fair and transparent estimate upfront


Input-Output Sensor Replacement Service

What is the Input-Output Sensor all about?

In order to operate properly, your vehicle requires a number of different electronic sensors. One of those is the input-output sensor (more commonly known as the vehicle speed sensor) on the transmission.

The input-output sensor consists of two different sensors, an input sensor and a separate output sensor, that work in tandem. While both are mounted in separate locations, their proximity enables them to share a wiring harness (the harness splits into two at the attachment point for the sensors). The physical location of the input-output sensors will vary depending on the make and model in question.

Both sensors work in conjunction to tell the transmission computer if the transmission is working properly. If the sensors detect a problem or erroneous operation, the computer will generally set a transmission fault code, which will need to be read using a computer scanner attached to the OBDII connector under the vehicle’s dash.

Keep in mind:

  • Both speed sensors work in tandem, but it’s possible for just one to fail.
  • Input-output sensors are not inspected regularly.
  • These sensors are subject to high heat.
  • If the sensors fail, the transmission may not shift properly.

Our recommendation:

It is essential that the transmission control module is able to determine if the system is working properly. If the input-output sensors are malfunctioning or have failed, the computer will attempt to put the vehicle into “limp home” mode. This allows the car to be driven, but limits the range of gears available (and the speed at which you can drive). Have any transmission problems inspected immediately by our expert mechanics.

What common symptoms indicate you may need to replace the Input-Output Sensor?

  • Vehicle downshifts hard
  • Transmission will only shift up to a specific point
  • Check Engine light is on

How important is this service?

Without a fully functioning transmission, your car is crippled. You will not be able to maintain highway or city speeds and can experience other shift-related problems. Have any transmission malfunction or Check Engine light diagnosed immediately.

Fast and easy Input-Output Sensor Replacement service at your home or office.


Recent articles & questions

How Long Does a Trunk Lock Actuator Last?
The The trunk of a car is designed to transport anything that the driver has that will not fit in the cabin of the vehicle. There are a variety of different mechanisms that allow the trunk to function as intended....
P0023 OBD-II Trouble Code: Camshaft Position B - Actuator Circuit (Bank 2)
P0023 P0023 code definition Camshaft Position B - Actuator Circuit (Bank 2) What the P0023 code means P0023 is the OBD-II generic code indicating the Engine Control Module (ECM) has determined that the bank 2 exhaust camshaft Oil Control Valve...
B1985 OBD-II Trouble Code: Seat Switch Lumbar Deflate Circuit Failure
B1985 means there the switch lumbar deflate circuit is bad. This is most likely due to a faulty circuitry in the part.

Starter cranks forever before the engine turns over

Your issue doesn’t appear to be a starter problem. The starter’s only job is to crank the engine. And from your description it is doing that (unless it is cranking very slow). Your problem seems to be that the engine...

Vehicle won't start. Battery no longer charges.

Hey there, thank you for asking about your 2008 Lexus RX350. Your car's alternator is responsible for charging the vehicle. When the car is running, the alternator and voltage regulator work to maintain the charge in your battery. When the...

Codes p0708 and p0706 show up i can drive and shift fine one trip the next trip it will act up.

Hi there. The P0708 trouble code (https://www.yourmechanic.com/article/p0708-obd-ii-trouble-code-transmission-range-sensor-circuit-high-input-by-andrew-quinn) means that the Engine Control Module (ECM) has detected a malfunction with the transmission range sensor. A mechanic would begin the diagnosis of the P0708 trouble code by finding the manufacturer’s suggested procedure...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com