Best Prices for Brakes must be pumped to work Inspection

Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM.

Estimate price near me

Service Location

Customer Ratings

(44)

How A Diagnostic Works

Instantly book a certified mobile mechanic to come to you

Mechanic diagnoses the problem and quotes necessary repairs

Your vehicle is ready to go

Fair, upfront & transparent pricing for all services

Our certified mobile mechanics can come to you now.

Customer Ratings

(44)


Brakes must be pumped to work Inspection Service

When you slow your car or decide to stop, you press the brake pedal. Most of the time, the pedal will be firm and you’ll be able to apply steady pressure until you reach the desired slower speed, or come to a complete stop. However, sometimes the pedal may “go to the floor” and you’ll have to pump it a couple of times to get the firm feel that you’re used to. If your brakes must be pumped to work, there’s a serious issue that needs to be addressed.

How this system works:

Your brakes work on fluid pressure. If the braking system isn’t able to build up the pressure necessary to operate the system, your pedal will feel strange. In some cases, it will be spongy and soft. In others, you’ll have to pump the brakes.

When you press the brake pedal, the master cylinder sends fluid into the lines, creating pressure. This activates the calipers, which squeeze the rotor on each wheel between the brake pads. Drum brakes work on a similar basis, but fluid pressure causes the actuator to press the shoes out against the sides of the drum to slow down the wheels.

Obviously, if there isn’t enough pressure in the lines, this doesn’t happen. However, if moisture has gotten into the system, the result can be similar. Water has a lower boiling point than brake fluid. When it’s heated at the brakes, it vaporizes, creating air in the lines (and allowing compression – brake fluid cannot be compressed).

Common reasons for this to happen:

  • Air in the Lines: The number one most common cause for having to pump your brakes to get them to work is air in the lines. This may be because your brakes were recently serviced but not bled correctly. It requires bleeding each wheel several times, starting with the wheels farthest from the master cylinder (passenger rear, driver rear, then passenger front and driver front). It can take multiple bleeds to remove all the air from the lines, even after a basic service. The fluid will then need to be topped off.

  • Low Brake Fluid: If your brake fluid is low (and it’s not due to brake pad wear), then the system will be unable to create enough pressure for normal operation and you may have to pump the pedal. Generally, low fluid is caused by a leak somewhere in the system, including at the caliper, the brake lines, or even the master cylinder.

  • Failing Master Cylinder: While rare, master cylinder failure does occur. If the master cylinder has begun leaking fluid down the back of the engine, you can expect to experience poor brake operation and reduced safety on the road.

  • Moisture in the Fluid: If your brake fluid has absorbed moisture (which is normal over time and through regularly wear and tear), you’ll notice reduced braking performance, including the possibility that you’ll have to pump the brake pedal in some situations.

  • Damaged or Missing Bleeder Valve: Each wheel should have a brake fluid bleeder valve on the line near the wheel hub. If one of yours has been damaged, it’s possible that you’re leaking fluid and allowing air into the line at the same time.

What to expect:

A top-rated mobile mechanic will come to your home or office to inspect your car’s brake system. The mechanic will visually inspect the master cylinder, the brake lines, calipers, and the rest of the system in order to determine the underlying cause of the problem. The mechanic will then provide a detailed inspection report that includes the scope and cost of the necessary repairs.

How it's done:

The mechanic will need to inspect the entire brake system, which may require the removal of one or more wheels. The mechanic will also need to check for air in the lines, as well as leaks in the lines and at the master cylinder.

How important is this service?

If your brakes have to be pumped to work, your system needs immediate service. This indicates a significant problem, including air in the lines. It reduces your stopping capability on the road, which endangers you, your passengers, as well as others on the road. One of our mechanics can diagnose and repair the problem, ensuring that you’re safe while driving.


Recent Brakes must be pumped to work Inspection reviews

Excellent Rating

(44)

Rating Summary
44
0
0
0
0
44
0
0
0
0

Shawn

13 years of experience
379 reviews
Shawn
13 years of experience
Toyota Tacoma L4-2.7L - Brakes must be pumped to work - Phoenixville, Pennsylvania
great overall knowledge, went above and beyond to diagnose/advise next steps even if the issue was out of scope. always super awesome to meet someone with a triple threat of experience, enthusiasm and customer service skills!

Keven

8 years of experience
187 reviews
Keven
8 years of experience
Mazda Protege L4-1.6L - Brakes must be pumped to work Inspection - Lakewood, Washington
Keven was very thorough and professional. He was very clear with what my car needed and gave me good advice and options. I will definitely book him for future appointments.

Jimmi

28 years of experience
343 reviews
Jimmi
28 years of experience
GMC Safari V6-4.3L - Brakes must be pumped to work Inspection - Casselberry, Florida
Jimmi was great to work with! He let me know when he was on his way over, and he was super professional while he checked out my car. Once he figured out what service my car needed, he explained everything thoroughly, including prices, and helped set me up with a convenient time to come back to complete the repairs. I would definitely work with Jimmi again for future maintenance and repairs!

Christopher

11 years of experience
125 reviews
Christopher
11 years of experience
Toyota 4Runner V6-3.4L - Brakes must be pumped to work - Spring, Texas
Christopher showed up on time, was very polite and thorough. I appreciated all the feedback and recommendations. He clearly communicated the repairs that were needed. Appreciated his diligence.

Recent articles & questions

Symptoms of a Bad or Failing Valve Cover Gasket
Common signs of a faulty gasket include a burning oil smell, dirty valve cover, oil leaks, low engine oil, and a rough-running engine that misfires.
How Long Does a Transmission Position Sensor (Switch) Last?
All All automatic transmission vehicles have a safety switch in place that only allows them to start if they are in park or neutral gars. The transmission position sensor, also called the transmission position switch, ensures the vehicle is in...
P0420 OBD-II Trouble Code: Catalyst System Efficiency Below Threshold (Bank 1)
P0420 code means that either the upstream or downstream oxygen sensor in the catalytic converter is not working. Replacing these parts can fix P0420.

How do I replace the front turn signal, parking light or side marker bulb?

Your car uses the same bulb for the front turn signal, parking light and side marker. Like the rest of the lights on your car, these will eventually burn out and need to be replaced. Here’s how to install a...

Intermittent starting issues

Hello. There are two easy ways to test a starter. One is to measure the voltage present at the starter terminals when cranking the vehicle. Another way is to test the starter with a starting system tester directly at the...

Smell of burning rubber after I changed the belt

You may have one or more pulley with a bad bearing that is causing the pulley to not turn with the belt, causing the burning of the belt. Have the pulleys monitored while holding the engine at 2500 RPM in...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

+1 (855) 347-2779 · hi@yourmechanic.com