Q: Wrench light comes on and chokes, loud grinding noise when I go slow
A few days ago I was at a stop light and when I went to accelerate a wrench came on and my car started choking until I shut it off myself. I shut it off and started it up and it worked fine for 2 days then when I went to leave for work today I started it and it took a few seconds to catch. Then when I went to leave it showed the wrench sign again and choked until I shut it off. I went start it again and I took a second to catch but I did and drive okay. After the first time it did this I can feel and hear a loud grinding noise when I driving at slow speed so and braking. I don't know if they are related but I know they started at the same time. I've never seen the wrench light come on before and it's the only one that does come on not the engine light
My car has 80000 miles.
My car has an automatic transmission.
The statements expressed above are only for informational purposes and should be independently verified. Please see our
terms of service
for more details
Get an instant quote for your car
Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing
What others are asking
What is the front passenger sensing system?
Your car’s air bag system is very advanced and capable of monitoring many different things. The front passenger sensing system is designed to tell the car’s computer a lot of different things about what’s going on with the passenger front...
Vehicle pulling to the right.
I first have to assume you are talking about one issue and not two different complaints. I would have to say your wheel bearing on the right is grinding or the brakes have locked up on that same wheel. The...
Bad control arm bushings--how to recognize
The control arm (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-control-arm-assembly) does what it says - it controls the wheel. There are two parts down and one part where the wheel is and it has a top and bottom. So if the bushings go bad, you get...
Squealing sounds when the truck is under load
Hello. Firstly, I suggest checking for vacuum leaks, the turbo piping for leaks, and the exhaust tubing that goes to the EGR valve for any cracks. Any of those conditions could cause high pitched noises. I've noticed that a few...
Car won't start, latching noise
If when turning the key you hear a loud click or latching noise, that may be the starter gear kicking out to contact the engine flywheel in an attempt to start. Test the battery (https://www.yourmechanic.com/services/service-battery-cables) while trying to start the...
Transmission problem 1998 Ford Explorer
Hello. The most likely cause is with the shift solenoids (https://www.yourmechanic.com/services/shift-interlock-solenoid-replacement) in transmission and/or valve body components. It is also possible that you could have an external electrical problem because the PCM also controls shift points. However, the most common...
Can a purge solenoid cable cause a EVAP leak code?
Hi, thanks for your question. When the engine is off, the vent shutoff valve and canister purge valve are closed. The fuel can't escape into the atmosphere. When the engine starts, the purge valve on the canister opens to allow...
My truck is stuck in 4L or 4H also the speedometer is saying I'm going 100 mph when I'm only going 20 mph. Is my GEM Module bad?
Hi there. The issue could be with the output shaft speed sensor on the tail shaft of the transfer case. The output shaft speed sensor is a sensor the registers the speed of the output shaft and lets the computer...
What are the best brake pads to get for my volvo c70? I am in rushhour traffic and I travel to the beach.
The best brake pads and rotors for your car are those supplied by Volvo. Nowadays, those parts can be obtained from legitimate Internet Volvo dealers at a discount off of what you would pay at a local Volvo dealer. If...
Related articles
P0078 OBD-II Trouble Code: Exhaust Valve Control Solenoid Circuit (Bank 1)
P0078 P0078 code definition Exhaust Valve Control Solenoid Circuit (Bank 1) What the P0078 code means P0078 is a generic OBD2 code indicating that the Engine Control Module (ECM) has tried to control the Bank 1 exhaust valve control solenoid,...
P0418 OBD-II Trouble Code: Secondary Air Injection System Relay A circuit Malfunction
P0418 indicates that a problem has occurred in the secondary air injection system which causes engine hesitation when accelerating and stalling.
How to Replace a Vacuum Hose
A vacuum hose is failing if the Check Engine Light comes on, the engine does not run smoothly, or the engine loses power and does not start.
Browse other content
Cities
Maintenance
Services