Q: How much would it cost to replace the crankshaft on a 2008 M3 Coupe?
I have a crankshaft that has begun to knock from rod bearing failure. I would like to replace the crankshaft but am not sure what a good price would be.
My car has 87000 miles.
My car has an automatic transmission.
The statements expressed above are only for informational purposes and should be independently verified. Please see our
terms of service
for more details
Get an instant quote for your car
Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing
What others are asking
There’s a big lag with the throttle
Hello, being a drivability issue it will require some diagnosis with a technician. If you can demonstrate it to the technician it would aid in diagnosis. It sounds like you might have low fluid level based on how you say...
Car stalling; gas smell
Hello. If you smell gas and it is stalling then you either have an internal or external fuel leak. If there is not any fuel hitting the ground and the smell is coming from the exhaust, then you either have...
Car shakes violently and 'check engine' flashes
Since you are only getting a misfire on cylinder number 3 specifically, this informs me that the cylinder ignition is not the problem. Since the engine has a coil pack that powers two cylinders at the same time and if...
Buzzing noise wheels steering
Hello. This can be caused by a number of things. Most of the time it is due to a brake pad sensor rubbing on the rotor. Once it does this long enough, it will break and the noise will stop....
Would the TPS be the same as an APPS for a diesel
The throttle position sensor on this diesel is the APPS mounted on fuel pedal.
The check engine light and the VSA came on at the same time. Is the van (Honda Odyssey 2010) ok to drive.
VSA is Honda's name for the electronic stability control system. Most vehicles today have it and use different names. The stability system usually piggy backs on the anti-lock brake system, using the same wheel speed, brake light, steering angle, and...
Will not shift and stuck in 1st gear.
Hi there. If the battery keeps going dead overnight, then there is a parasitic load applied to the battery. Charge the battery (https://www.yourmechanic.com/services/battery-replacement) to a full charge of 12.6 volts. With the battery installed in the car, remove the negative...
When i put the truck in 4x4 it makes a creaking noise and when i start to make a turn the truck wont turn all the way
Hey there. It is possible that it may be time to change the differential fluid, as this symptom is common when the differential fluid is dirty or low. This service is typically due every 100,000 miles. It is also possible...
Steering pump issue 2006 Ford Escape
Hi there - there are a couple of possibilities for this "hard steering" (https://www.yourmechanic.com/question/could-the-power-steering-pressure-sensor-cause-my-steering-wheel-to-be-hard-or-hard-to-steer-by-davon) behavior. It is possible that there is still air in the system, although having driven it some, with many left/right turns, that should be a non-issue....
Related articles
A Buyer’s Guide to the 2012 BMW 1-Series
The The 2012 BMW 1-Series, which includes both the 128i and the 135i in both a coupe and convertible options, provides the perfect combination of power, performance and luxury. Designed with a focus on thrilling acceleration and a smooth, elegant...
BMW Certified Pre-Owned (CPO) Car Program
Shopping Shopping for a used BMW vehicle often leads many drivers to consider certified pre-owned options. BMW is one of many manufacturers that have a certified pre-owned (CPO) program. Each car manufacturer structures their CPO program differently; read on to...
P0337 OBD-II Trouble Code: Crankshaft Position Sensor A Circuit Low Input
P0337 means that the crankshaft is suffering because of low voltage. This could be due to sensor not being aligned properly or electrical problems.
Browse other content
Services
Maintenance