Q: CV boots need replacing

asked by on February 26, 2016

I believe the CV boots need replacing. Whenever the tires are turned there is a grinding noise. The brakes also need to be changed.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

Brake not working
The description given is rather vague. I'm not sure to what extent or in what way your right rear brake doesn't work. However, a brake problem that is exclusive to one wheel is usually caused by a faulty brake caliper....
Car doesn't move when put into reverse or drive
The transmission in your Equinox (the 4L60E) is common - I replaced one recently. I suggest starting by checking your transmission fluid level: Start your vehicle, let it warm up, and with a rag, pull up the transmission dipstick tube...
Clutch is chattering
A chattering clutch may be caused by a warped clutch pressure plate or flywheel. On some cars these warp due to the clutch release system or clutch pedal mechanism binding and not releasing smoothly. I would recommend having the complete...
Car starts, then dies
Hello. From what you are describing, it sounds like the mass airflow (MAF) sensor is not working properly (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-mass-airflow-sensor). The mass airflow (MAF) sensor helps to regulate the air/fuel mixture and the idle of the car. When the mass airflow...
Is it okay to drive 500 miles with a tire patch?
Hi, thanks for writing in. Depending on the severity of the surface area of the tire that has been patched and the location of the patch, this could be fine, but is not recommended. Sidewall patches are particularly vulnerable to...
Procedure to replace lower ball joints and sway bar links and torque specification for all the front end components
Hi there. To replace the ball joints you would need to jack up the vehicle and put it on jack stands. Remove the tires, calipers, and brake rotors. Then put a jack under the lower control arm and remove the...
The crankshaft sensor blows when car is put in reverse.
The problem is going to be caused by a short in the harness that goes down to the crankshaft sensor. Check to see if the motor and transmission mounts are broken allowing the engine to move too far and hitting...
2005 Dodge Dakota 6cyl 3.7 litre with auto trans. 110k miles. Transmission slipping when shifting. varies directly with the amount
Unless the fluid is obviously contaminated, and thus there is a possibility of a blocked transmission filter, I wouldn't start the diagnostic with a fluid/filter change. Eventually, you should change the fluid and the filter but more likely causes of...
Is bank2 sensor 1 upstream or downstream?
Hi there. When an oxygen sensor is referred to as upstream, it means it's located prior to the catalytic converter. On a 2006 Honda Accord V6, the Bank 2 Sensor 1 o2 sensor is located on the exhaust manifold; making...

Related articles

A Buyer’s Guide to the 2012 Dodge Charger
If If you’ve always loved driving performance cars but you don't know how you’ll fit a baby seat in a Mustang or a Camaro, the 2012 Dodge Charger could be the car for you. While it has the room and...
A Buyer’s Guide to the 2011 Dodge Dakota
2011 2011 marked the final year of production for Dodge’s venerable Dakota pickup truck. It was a compact pickup, not quite the size of the Ram, and competed with similar models like the Chevy S10 and the Ford Ranger (both...
How to Use “Stow ‘n’ Go” Seats in a Dodge or Chrysler Minivan
Minivans Minivans offer customers maximum interior space for the size of the vehicle. On a platform just a bit larger than a full size car, you can fit a driver and six passengers - or a driver, three passengers, and...