Q: 04 kia sedona cuts off when i press the brake
Just purchased an 04 Kia sedona last week. Ran fine for a day. Now it shuts off when you apply the brake. I have replaced numerous parts, checked numerous hoses and fuses and it's still cutting off when applying the brake. I can't find any one that's had a problem like this. Any suggestions are very much appreciated.
My car has 172000 miles.
My car has an automatic transmission.
The statements expressed above are only for informational purposes and should be independently verified. Please see our
terms of service
for more details
Get an instant quote for your car
Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing
What others are asking
Car does not start.
If the engine dies while driving and it is associated with an electrical service light, the issue is almost certainly the alternator. I would recommend having your starting system inspected (https://www.yourmechanic.com/services/car-starts-and-then-dies-inspection) for faults by a technician from YourMechanic. If the...
How do I see a list of all the paired phones?
The infotainment system can have five mobile devices paired to it at a time. To see which phones are currently paired to the system, press the Config button, and select Phone Settings. Then, select Bluetooth, followed by Device List.
intermittent screeching coming from front right passenger wheel when accelerating above 20mph.
To be safe, check to make sure that you are not having a problem with the engine belt slipping and causing the squealing noise. Also, make sure the metal backing plate behind the rotor is not too close and rubbing...
Car will not pick up until easing off the gas pedal, Infiniti G25
Instead of using a conventional mechanical throttle, your vehicle uses a "drive-by-wire" system. This design, throttle position, and accelerator pedal position are relayed to the control module via dedicated sensors. The control module then uses this information to control a...
Faulty brake lights in a Hyundai Getz
Hey there, thanks for writing in. If you have the center light working, then the brake switch is okay and you most likely have two bad bulbs in the lights. If you need help having this repaired, a certified pro...
P0340 - Where's the camshaft sensor circuit A bank 1 located on a 1994 Lexus ES 300
Hi, thanks for your question about the P0340 trouble code (https://www.yourmechanic.com/article/p0340-obd-ii-trouble-code-camshaft-position-sensor-circuit-malfunction-by-jamahl-walker). The camshaft sensor (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-camshaft-position-sensor) on the Lexus ES300 should be located toward the back of the motor on the right side (assuming you are facing the motor) near the...
Stalling at red lights, and sputters sometimes when I press the gas.
This may be a sign of a failing idle air control valve. The idle air control valve monitors the air intake as it is mixed with fuel prior to being injected into the engine. This valve is controlled by the...
Front End Thumping Noise
Hi there: At first glance, I'd believe this noise is caused either by faulty wheel bearings or perhaps a warped brake rotor. However, it is very difficult to duplicate a road noise issue inside a shop or on a rack....
Where can I locate the starter in a 2012 Kia Forte Koup with a 2.4L engine?
The starter (https://www.yourmechanic.com/services/starter-replacement) on your vehicle should be located down on the left hand side of the motor close to the oil pan. If you need additional help with this, please contact YourMechanic to schedule an appointment as we are...
Related articles
10 Biggest Car-Related Headaches and What to Do About Them
You You don’t want to, but if you're a car owner it's inevitable that at some point you will experience car troubles. It's also fairly certain that the machine you rely on will cause you grief when you least expect...
Symptoms of Bad or Failing Brake Pads
If your brakes are noisy, the brake pedal is pulsating, or the brakes are responding poorly, you may need to replace the brake pads.
How to Replace an ABS Control Module
An ABS module can be a difficult part to replace depending on the manufacturer's design. You may need to reprogram and bleed the system if necessary.
Browse other content
Services
Maintenance