Mercedes-Benz 300SE Power Steering Pressure Hose Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(12)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(12)

Power Steering Pressure Hose Replacement Service

How much does a Power Steering Pressure Hose Replacement cost?

On average, the cost for a Mercedes-Benz 300SE Power Steering Pressure Hose Replacement is $332 with $192 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1990 Mercedes-Benz 300SEL6-3.0LService typePower Steering Pressure Hose ReplacementEstimate$554.08Shop/Dealer Price$656.91 - $949.79
1991 Mercedes-Benz 300SEL6-3.0LService typePower Steering Pressure Hose ReplacementEstimate$544.17Shop/Dealer Price$643.59 - $933.93
1993 Mercedes-Benz 300SEL6-3.2LService typePower Steering Pressure Hose ReplacementEstimate$569.89Shop/Dealer Price$675.79 - $985.45
1992 Mercedes-Benz 300SEL6-3.2LService typePower Steering Pressure Hose ReplacementEstimate$569.89Shop/Dealer Price$675.79 - $985.45
Show example Mercedes-Benz 300SE Power Steering Pressure Hose Replacement prices

What is the power steering pressure hose and how does it work?

The power steering pressure hose transfers the high-pressure hydraulic output of the power steering pump to either a steering gear box or steering rack and pinion unit to create the power assist that you rely on when you turn the steering wheel. The pressure hose is only used in cars with a power steering pump and reservoir, so if you have a newer car you may have electric power steering instead. The pressure hose is relatively large in diameter in order to withstand high hydraulic pressure, flex as the engine moves and vibrates, and also withstand engine heat, accidental cuts, and abrasion.

When to the consider replacing the power steering pressure hose:

  • Groaning, whirring noise or difficulty steering. Noise, or difficulty turning the steering wheel, may reflect a low power steering fluid level, which could be due to a leak in a pressure hose, or a leak elsewhere in the power steering system. Although a leak in the pressure hose is a possible cause of a low fluid level, a mechanic will consider all other possible causes, too.
  • Visible fluid leaks. There are usually steel ferrules clamped onto each end of the rubber pressure hose. These ferrules are common leak points. If there is seepage from these ferrules, the pressure hose should be replaced.
  • Hose damage. If the hose has significant physical damage, such as cuts, abrasions, cracks, or heat damage, the hose should be replaced to avoid sudden hose failure.
  • Contaminated fluid. If rubber particles are found in the power steering fluid or reservoir, it means the interior of either the pressure hose or the return hose is deteriorating. All rubber hoses should be replaced and the system flushed. An in-line, aftermarket fluid filter might be required.
  • Hose age. Both the pressure and return hoses are rubber-based products with a limited service life. If the vehicle is more than 10 years old, and power steering components are being replaced, all the rubber hoses should be replaced during that service.

How do mechanics replace the power steering pressure hose?

The underhood routing of the power steering pressure hose varies greatly between car models. The repair procedure ranges from simple to quite involved. The basic steps are:

  • Raise car as needed and support with steel safety stands.
  • Unthread the pressure hose tube nuts, or banjo-style bolts, at each end of the pressure hose.
  • Remove pressure hose and inspect interior hose lining for separation, if visible.
  • Install a new hose, using a new sealing washer or O-ring seals as applicable, and paying particular attention to the required original equipment manufacturer’s (OEM) torque value for the tube nuts or banjo bolts. Replace rubber return hose, if required, and with the authorization of the customer.
  • Once the system is fully sealed again, bleed or flush power steering system as required to remove all air and contaminants.
  • Finally, the engine is run, the car is test driven, and leaks are checked for at all connections.

Is it safe to drive with a power steering pressure hose problem?

No. The fluid in the power steering pressure hose is under very high pressure and flammable. A leak that sprays fluid into a hot engine part, such as the exhaust manifold, can cause a fire. Leaks that cause significant fluid loss can cause difficulty in steering and, if a leak causes the fluid level in the reservoir to drop too low, it can cause damage to the power steering pump too, necessitating the installation of not only a new hose but a new pump.

When replacing the power steering pressure hose keep in mind:

  • When the power steering hoses are replaced, the entire power steering system should be inspected.
  • Use only OEM specified power steering fluid in your power steering system.
  • If the pressure hose has deteriorated from the inside, the rubber return hose should be replaced as well and the system should be flushed. A mechanic might recommend the installation of an in-line filter to capture all debris.
  • Tube nuts and banjo bolts used to seal pressure hoses have OEM-specified torque values. Mechanics will use a calibrated torque wrench to tighten the connections.
  • Complete removal of air from the system can occasionally take some time, even after the normal bleeding procedure. During this time some mild noise may be heard when turning the steering wheel. If it persists more than a day or so, the system should be rechecked.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(12)

Rating Summary
10
1
0
0
1
10
1
0
0
1

Nick

15 years of experience
90 reviews
Nick
15 years of experience
Mercedes-Benz 300SE L6-3.0L - Window Regulator Replacement (Driver Side Front) - Sacramento, California
excellent service..conciencence service.and cleanup.

Dave

24 years of experience
303 reviews
Dave
24 years of experience
Mercedes-Benz 300SE L6-3.0L - Car is not getting enough power - San Jose, California
Dave has integrity which I highly value.

Nickolas

7 years of experience
54 reviews
Nickolas
7 years of experience
Mercedes-Benz 300SE L6-3.2L - Oil Change - Olathe, Kansas
Was interesting and great work!

Richard

20 years of experience
97 reviews
Richard
20 years of experience
Mercedes-Benz 300SE L6-3.0L - Car is not starting - Fayetteville, North Carolina
Richard did a great job finding and diagnosing problem. I really appreciate it. Thank you Richard

Excellent Rating

(12)

Rating Summary
10
1
0
0
1
10
1
0
0
1
Number of Mercedes-Benz 300SE services completed
132+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

What Causes a Car to Stall?
You trust your car. You may not think about it, but you believe that certain functions will occur without fail. You may be aware...
P0798 OBD-II Trouble Code: Pressure Control Solenoid “C” Electrical
P0798 means there is a problem with the electronic pressure control solenoid or solenoid circuit due to low or dirty transmission fluid.
Symptoms of a Bad or Failing Rear Window Transmission
If you hear squealing noises or the window jerks, stops moving halfway, or doesn't move at all, get the rear window transmission inspected.

How do I extend the seat belt?

If your seat belt is not long enough to safely and properly buckle around you, you will need to get a seat belt extender, which adds eight inches to the seat belt length. To receive a seat belt extender, visit...

Sounds when turning.

This may be a sign of failing or worn out wheel bearings. A wheel bearing will usually fail due to pitting or small damage on the surface of the rollers or the bearing race. Both the surface of the rollers...

Transmission not shifting

It sounds like you may be low on transmission fluid (https://www.yourmechanic.com/services/transmission-fluid-service) or have a faulty transmission control solenoid. As you know, automatic transmissions use pressurized hydraulic fluid to change gears. Every time a gear change is required, the car's computer...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com